Earlier this year, along Highway 8, a car crash smashed into an old lilac.

The lilac was a very old shrub. It must have been there for a couple of decades at least. Some of its trunks were three to four inches wide, and there were eight to ten of those stems spreading out from the root base. The stems reached about the height of the wall of the house, about a story high.

It was a large, old, established shrub, and after the accident, it needed to be removed completely.

I don’t currently use heavy machinery for this kind of work. An excavator, for example, is heavy, expensive for the client, and requires additional costs such as renting and transportation to the site. And then you’re operating it for a very short period of time to remove a single shrub.

So, if possible, I tend to do these kinds of jobs without heavy machinery.

The challenge is not necessarily whether I have enough strength to remove a shrub of this size. It’s finding ways to apply that strength effectively, without exhausting myself in the process. I still have the rest of my gardening day to get through, and the rest of the season.

Clearing the Way

My main tools for this job were a heavy-duty shovel, a garden fork, hinged loppers, a reciprocating saw (Sawzall), a crowbar, a rake, gloves, and a wheelbarrow.

The shovel has an extra-long handle made of a compound material, something like fiberglass rather than wood. It can withstand a fair bit of leverage, although it isn’t indestructible. The hinged loppers allow me to apply a little extra force when cutting thicker branches.

Before starting a large plant removal, I always check what the approach will be for disposing of the yard waste. This was a farm property, and there was a large burn pile where the woody material could go.

There was also some poison ivy on the site. I collected the poison ivy separately in a yard waste bag, along with some of the green material. Poison ivy should never be burned. The irritating oils can become airborne in the smoke, and inhaling them can cause severe complications. Disposal should follow local yard waste rules, since not all municipal collection programs accept poison ivy.

I started by clearing everything accessible around the shrub. There were some weeds, some little tree seedlings that had sprouted this year, and a young Manitoba maple, perhaps a couple of years old and a few feet tall.

I removed the surrounding weeds, both woody and perennial, to see what I was doing.

Lilacs are often multi-stemmed shrubs. They also tend to spread by suckers, sending up new stems around the original plant. Sometimes an old lilac can have many suckers filling in the surrounding area.

In this case, the shrub was growing in a fairly narrow space, with only a couple of neighboring suckers. Those were easily pulled.

The larger stems were coming from a central root base, dividing into finer and more numerous branches as they got taller, forming the crown of the shrub.

I started with the loppers, removing branches thin enough to be cut by hand, from about a quarter of an inch up to perhaps two inches wide. I set these aside in a pile.

Once the smaller branches were removed, I took the reciprocating saw and carefully removed the larger ones.

For many of the branches, I made two cuts: one higher up, and then another lower down. This way, I was dealing with smaller pieces of woody material. It was easier to control where the branches fell, and there was less risk of a heavy branch collapsing onto the saw.

Eventually, I had cleared most of the top of the shrub.

But I deliberately left one thick branch, about two feet long, sticking out of the base.

I would need it later.

Removing the Stump

This is the hard part.

People often think that when a tree or shrub is well established, it must have a massive root system underneath it. To a certain extent, that’s true. But the part you actually need to remove is often not as big as you think.

The key thing is that the root system isn’t just one big blob under the ground.

It’s a series of individual roots.

Those individual roots are attaching the plant to the ground. If you can sever them, one by one, you can eventually free the central root mass.

There may still be roots left in the surrounding soil afterward. Some can be pulled out or dug out, and others can be left to decompose, provided they’re not capable of resprouting. With a suckering shrub such as a lilac, it’s worth keeping an eye out for any remaining growth.

The goal here was to create a fresh garden bed that could be planted again, without the previous shrub coming back.

Of course, you can’t start sawing away at roots if you don’t know where you’re sawing.

So I started digging.

I took my shovel and dug around the circumference of the root ball. I made an initial pass, then went around a second time, looking for where I could get the shovel deeper, where the roots were most firmly attached, and where I could find clear points to cut.

Once I had exposed some of the larger roots, I used the reciprocating saw to sever them.

For some roots, I made two cuts, perhaps two or three inches apart, and removed that little section of root entirely. This created a gap where I could get my shovel in and continue digging deeper.

I repeated this around the entire circumference of the shrub.

Eventually, I started being able to move the root ball a little bit.

And this is the key point you’re looking for.

Finding the Wiggle

If you keep digging and cutting and you’re still not able to get a wiggle out of the root ball, you have a big uphill battle ahead.

But if you can get a wiggle, you can start sensing where the roots are still attached and where you have some room to move.

Depending on which direction the root ball was wiggling, I could make a reasonable guess about where it was still most firmly attached to the soil.

That gave me hints about where to dig next.

I would expose another root, cut it with the saw, and then try moving the root ball again.

This is where the branch I had left sticking out of the stump became very helpful.

It was about two feet long and thick enough that I could use it as a lever. I could grab it with both hands and rock it back and forth, applying my body weight to the movement.

Instead of trying to pull the whole root ball straight out of the ground, I could use that branch to feel where the resistance was coming from.

I also used a crowbar to get some extra lift underneath the root ball. My heavy-duty shovel can do a fair bit of levering, but there’s a limit to what I want to ask of it. A crowbar is better suited to applying that kind of force.

So I kept alternating between rocking the root ball, digging to expose the remaining roots, and cutting them.

One by one, the attachments gave way.

Eventually, there was so much give that I could simply rock the remainder back and forth until it freed itself completely from the soil.

The entire root ball was out.

Moving the Root Ball

At this point, I had a fairly substantial mass of roots sitting beside a hole in the garden.

I didn’t have a scale, so I couldn’t tell you exactly how much it weighed. But it was heavy enough that picking it up would have required a lot of exertion.

And even if I could lift it, why would I?

I still had the rest of my gardening day to get through.

One thing I’m always looking for in my work is how to preserve energy. Not simply to get through the current task, but to have enough energy for the next job, the next day, and the rest of the season.

Heroics can be fun, but they’re not necessarily a good strategy for endurance.

I had a wheelbarrow nearby.

So instead of trying to lift the root ball up and over the edge, I tipped the wheelbarrow onto its side, resting it against the ground.

Then I wiggled the root ball over until it was nestled inside the cavity of the wheelbarrow.

From there, I could upright the wheelbarrow by lifting it from the side on the ground, like a weighed squat, bringing the root ball with it.

Now the weight was resting in the wheelbarrow rather than in my arms.

I wheeled it over to the burn pile, along with the rest of the branches I had removed.

No excavator, and no heroic lifting required.

Leaving the Garden Ready

Once the shrub was removed, the space was cleared, but it was still a messy one.

There was a fair bit of soil piled around the hole from all the digging.

I shoveled the soil back into place, gently firmed it down with my feet, and then raked the remaining soil over to even out the surface.

Finally, I raked over the entire garden bed.

There was still some mulch left in the area. I’ll be planting that bed later, and probably remulching it, but for now the job was to remove the shrub and leave the space ready for the next step.

And that was it.

The Strange Occurrence of an October Lilac Bloom

There was one last detail.

Despite the accident, and despite the damage that had made its removal necessary, the old lilac still had some life in it.

It had put out a bloom.

In October.

Lilacs are spring-flowering shrubs, although some varieties have been bred specifically to rebloom later in the season. This one was likely an old variety, your typical lilac-colored lilac.

I’ve encountered a random lilac bloom in October before, but very seldom. It’s a strange occurrence.

I took the flower and smelled it.

It smelled like spring in fall.

Lilac removed October 6th

Published October 19th